How To Hook Up Onn Soundbar To Tv
onn 2.0 Channel Soundbar User Guide
USER Transmission INSERTS FOR FCC ID
- Warning: Changes or modifications to this unit of measurement not expressly approved past the political party responsible for compliance could void the user'south say-so to operate the equipment.
- NOTE: This equipment has been tested and constitute to comply with the limits for a Course B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if non installed and used in accordance with the instructions, may crusade harmful interference to radio communications.
Nonetheless, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which tin exist determined by turning the equipment off and on, the user is encouraged to endeavor to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.
- Increase the separation betwixt the equipment and receiver.
- Connect the equipment into an outlet on a circuit unlike from that to which the receiver is continued.
- Consult the dealer or an experienced radio/TV technician for assist.
- This device complies with Part 15 of the FCC Rules. Functioning is subject area to the following 2 conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may crusade undesired operation.
- RF Exposure Statement
To maintain compliance with FCC's RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your trunk: Use but the supplied antenna.
Parcel contents
- Soundbar 1pc
- 3.5mm audio to RCA audio cablevision (Length: ane.5m) 1pc
- Remote control 1pc
- Product Guide 1pc
- External adaptor 1pc
Speaker Overview
- Status indicator
- Wall mount
- Aux in
- Optical
- Power
- Power on / off
- Source
- Volume down
- Volume upward
Status indicator
Standby | Solid Red |
Optical | Solid Dark-green |
Aux in | Solid White |
Bluetooth pairing mode | Flashing blue |
Bluetooth device continued | Solid blue |
Volume up and downward | Corresponding to the sound source indicator light flash 1 time |
Maximum and minimum volume | Corresponding to the sound source indicator light flash three times |
Mute | Slow flash |
Television mode | Corresponding to the sound source indicator light flash 2 times |
Music way | Corresponding to the sound source indicator low-cal wink 2 times |
Movie mode | Corresponding to the sound source indicator light flash ii times |
Specifications
- Output Power: 12.5W x 2(RMS)
- Frequency Response: 50Hz~20 KHz
- S/N Ratio: ≥65dB
- Separation: ≥45dB
Remote control
- Ability on off
- Mute
- Bluetooth
- Aux
- Optical
- TV way
- Music manner
- Motion picture mode
- Volume upwardly
- Previous track
- Play / Pause
- Next rail
- Volume downwards
Remote command Batteries
Earlier get-go utilize
To prepare the remote command for first utilise, pull out the condom strip to actuate the bombardment.
Replacing the battery
When replacing the battery in the remote control, refer to the diagram below.
- Printing the catch across.
- While holding the catch, open the bombardment door.
- Fit the bombardment observing ploarity as shown. When replacing the battery, utilise only the same CR2025 type specified.
Power and connectedness
- Plug the DC cablevision from the AC adaptor into the Power jack on the
back panel, and plug the AC adaptor into the wall socket. - Press to power on/power off.
- Connect the audio cablevision to the audio output of whatsoever device (such Desktop PC, Laptop, Smartphone Tablet, MP3, TV etc.)with a 3.5 mm headphone output jack or RCA output jack.
Bluetooth® Connectedness
- Turn on the audio bar and select the Bluetooth® style.
- Activate the Bluetooth® office on your device and search for devices nearby.
- Find "Onn xvi" Soundbar" in the search results and tap to connect.
- The Bluetooth® indicator will turn solid blue on upon a successful connection.
Note:
- The Bluetooth indicator volition go on flashing when the sound bar is pairing.
- Please make sure no other agile Bluetooth® devices are within range, and that the sound bar is within 3ft / 1m away from your device.
- Before starting to play via Bluetooth, delight lower the volume to a moderate level.
onn 2.0 Aqueduct Soundbar User Guide – Download [optimized]
onn two.0 Channel Soundbar User Guide – Download
Source: https://manuals.plus/onn/onn-2-0-channel-soundbar-user-guide
0 Response to "How To Hook Up Onn Soundbar To Tv"
Post a Comment