Dji Inspire 1 V2 0 Test
FCC PART fifteen.247 Test Written report For SZ DJI Engineering CO., LTD 14th floor, West Wing, Skyworth Semiconductor Design Building NO.18 Gaoxin South 4th Ave, Nanshan, Shenzhen, Guangdong, China FCC ID: SS3-WM6101510 Report Type: Production Type: Original Report DJI Inspire 1 V2.0 Test Engineer: Report Number: Allen Qiao RDG151015004-00A Report Date: 2015-10-21 Reviewed By: Sula Huang RF Leader Test Laboratory: Bay Area Compliance Laboratories Corp. (Dongguan) No.69 Pulongcun, Puxinhu Industrial Zone, Tangxia, Dongguan, Guangdong, Communist china Tel: +86-769-86858888 Fax: +86-769-86858891 www.baclcorp.com.cn Note: This test written report is prepared for the customer shown above and for the device described herein. Information technology may not exist duplicated or used in office without prior written consent from Bay Area Compliance Laboratories Corp. (Dongguan). Bay Surface area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A TABLE OF CONTENTS Full general Data .......................................................................................................................................4 Production DESCRIPTION FOR EQUIPMENT UNDER Examination (EUT) .....................................................................................4 OBJECTIVE ...................................................................................................................................................................4 Test METHODOLOGY ..................................................................................................................................................four Exam FACILITY .............................................................................................................................................................4 SYSTEM Examination CONFIGURATION ..........................................................................................................................5 DESCRIPTION OF TEST CONFIGURATION ......................................................................................................................5 EUT EXERCISE SOFTWARE ..........................................................................................................................................5 EQUIPMENT MODIFICATIONS .......................................................................................................................................5 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................5 SUMMARY OF TEST RESULTS ...............................................................................................................................6 FCC §15.247 (i) & §1.1307 & §2.1091- MAXIMUM PERMISSIBLE EXPOSURE (MPE).........................................seven APPLICABLE STANDARD ..............................................................................................................................................7 FCC §fifteen.203 - ANTENNA REQUIREMENT.............................................................................................................8 APPLICABLE STANDARD ..............................................................................................................................................viii ANTENNA CONNECTOR Structure ......................................................................................................................8 FCC §15.209, §15.205 & §15.247(d) - SPURIOUS EMISSIONS...............................................................................9 APPLICABLE STANDARD ..............................................................................................................................................9 MEASUREMENT UNCERTAINTY ....................................................................................................................................nine EUT SETUP ..................................................................................................................................................................9 EMI Test RECEIVER & SPECTRUM ANALYZER SETUP ..............................................................................................x TEST Procedure ......................................................................................................................................................10 CORRECTED Aamplitude & MARGIN Calculation .................................................................................................11 Examination EQUIPMENT LIST AND DETAILS .........................................................................................................................11 TEST RESULTS SUMMARY ..........................................................................................................................................xi Exam DATA ................................................................................................................................................................11 FCC §fifteen.247(a) (2) – 6dB BANDWIDTH..................................................................................................................19 Applicable STANDARD ............................................................................................................................................19 TEST PROCEDURE ......................................................................................................................................................19 Test EQUIPMENT List AND DETAILS .........................................................................................................................nineteen Exam Information ................................................................................................................................................................nineteen FCC §15.247(b) (iii) - MAXIMUM PEAK CONDUCTED OUTPUT POWER ......................................................27 Applicable STANDARD ............................................................................................................................................27 TEST Procedure ......................................................................................................................................................27 Exam EQUIPMENT LIST AND DETAILS .........................................................................................................................27 TEST DATA ................................................................................................................................................................28 FCC §15.247(d) – 100 kHz BANDWIDTH OF FREQUENCY BAND Border .......................................................29 APPLICABLE STANDARD ............................................................................................................................................29 TEST Process ......................................................................................................................................................29 TEST EQUIPMENT Listing AND DETAILS .........................................................................................................................29 TEST DATA ................................................................................................................................................................29 FCC §15.247(e) - POWER SPECTRAL DENSITY .................................................................................................34 APPLICABLE STANDARD ............................................................................................................................................34 FCC Office xv.247 Folio ii of 47 Bay Surface area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Exam PROCEDURE ......................................................................................................................................................34 TEST EQUIPMENT Listing AND DETAILS .........................................................................................................................34 Examination Data ................................................................................................................................................................34 FCC Role 15.247 Page 3 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Study No.: RDG151015004-00A GENERAL Data Production Clarification for Equipment under Test (EUT) The SZ DJI Engineering CO., LTD's product, model number: T601 (FCC ID: SS3-WM6101510) (the "EUT") in this report was a DJI Inspire one V2.0, which was measured approximately: 46cm (L) 10 44 cm (W) ten 31 cm(H), rated input voltage: DC 22.2V from lithium battery. * All measurement and exam information in this report was gathered from product sample series number: 151015004. (Assigned by BACL.Dongguan). The EUT was received on 2015-10-x. Objective This study is prepared on behalf of SZ DJI Applied science CO., LTD in accordance with Part 2, Subpart J, Part 15, Subparts A, B and C of the Federal Communications Commission'southward rules The tests were performed in order to make up one's mind the compliance of the EUT with FCC Part 15-Subpart C, section 15.203, fifteen.205, 15.207, 15.209 and fifteen.247 rules. Test Methodology All measurements contained in this study were conducted with ANSI C63.10-2013, American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices. All emissions measurement was performed and Bay Area Compliance Laboratories Corp. (Dongguan). Test Facility The Test site used by Bay Surface area Compliance Laboratories Corp. (Dongguan) to collect examination information is located on the No.69 Pulongcun, Puxinhu Industrial Zone, Tangxia, Dongguan, Guangdong, Mainland china Examination site at Bay Expanse Compliance Laboratories Corp. (Dongguan) has been fully described in reports submitted to the Federal Communications Commission (FCC). The details of these reports accept been found to be in compliance with the requirements of Department 2.948 of the FCC Rules on February 06, 2015. The Federal Communications Committee has the reports on file and is listed nether FCC Registration No.: 273710. The test site has been approved by the FCC for public use and is listed in the FCC Public Admission Link (PAL) database. FCC Role 15.247 Page 4 of 47 Bay Expanse Compliance Laboratories Corp. (Dongguan) Study No.: RDG151015004-00A Arrangement Examination CONFIGURATION Clarification of Exam Configuration The system was configured for testing in Engineering Mode, which was provided past the manufacturer. For two.4G band, viii channels are provided to testing: Channel Frequency (MHz) 2406.five 2416.v 2426.5 2436.5 Aqueduct Frequency (MHz) 2446.5 2456.5 2466.5 2476.5 3channels were tested: 2406.5MHz, 2436.5MHz, 2476.5 MHz EUT Practise Software The software "DJI Become" was used for testing, which was provided past manufacturer. The maximum ability with 100% duty bicycle was configured past system default setting. Equipment Modifications No modification was made to the EUT. Block Diagram of Test Setup i.0 Meter EUT Non-Conductive Table 80 cm above Ground Aeroplane one.5 Meter FCC Office 15.247 Folio 5 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Written report No.: RDG151015004-00A SUMMARY OF Test RESULTS FCC Rules Description of Test Result §fifteen.247 (i), §1.1307 & §two.1091 Maximum Permissible Exposure (MPE) Compliance §xv.203 Antenna Requirement Compliance §xv.207 (a) Air conditioning Line Conducted Emissions Not Applicable §15.247(d) Spurious Emissions at Antenna Port Compliance §15.205, §15.209, §15.247(d) Spurious Emissions Compliance §xv.247 (a)(2) 6 dB Bandwidth Compliance §15.247(b)(iii) Maximum Peak Conducted Output Ability Compliance §xv.247(d) 100 kHz Bandwidth of Frequency Ring Border Compliance §15.247(e) Power Spectral Density Compliance Non Applicable: The EUT powered past lithium battery. FCC Part xv.247 Folio half dozen of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A FCC §15.247 (i) & §i.1307 & §2.1091- MAXIMUM PERMISSIBLE EXPOSURE (MPE) Applicable Standard According to subpart 15.247(i) and subpart §1.1307, systems operating under the provisions of this section shall be operated in a fashion that ensures that the public is not exposed to radio frequency energy level in excess of the Commission'due south guidelines. Limits for Maximum Permissible Exposure (MPE) (§1.1310, §ii.1091) (B) Limits for Full general Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/grand) Magnetic Field Strength (A/m) Power Density (mW/cm2) Averaging Time (minutes) 0.3–one.34 614 1.63 *(100) 30 ane.34–xxx 824/f ii.19/f *(180/f²) 30 xxx–300 27.5 0.073 0.two 30 300–1500 f/1500 30 1500–100,000 one.0 xxx f = frequency in MHz; * = Plane-wave equivalent power density; According to §i.1310 and §2.1091 RF exposure is calculated. Calculated Formulary: Predication of MPE limit at a given distance S = PG/4πR² = power density (in appropriate units, e.chiliad. mW/cm2); P = ability input to the antenna (in appropriate units, e.g., mW); Yard = power gain of the antenna in the management of interest relative to an isotropic radiator, the power gain cistron, is ordinarily numeric gain; R = distance to the heart of radiation of the antenna (appropriate units, due east.thousand., cm); Calculated Data: Frequency (MHz) 2406.5 Antenna Gain (dBi) (numeric) 2.00 Tune-upwardly Ability (dBm) (mW) 30 1000 Evaluation Altitude (cm) Ability Density (mW/cm2) MPE Limit (mW/cm2) twenty.00 0.40 1.0 Note: The tune-up power is 29+/-1dBm. Result: The device meet FCC MPE at 20 cm distance FCC Part xv.247 Page vii of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A FCC §xv.203 - ANTENNA REQUIREMENT Applicable Standard According to § xv.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, simply the user of a standard antenna jack or electric connector is prohibited. The structure and application of the EUT were analyzed to determine compliance with section §15.203 of the rules. §xv.203 state that the subject device must meet the following criteria: a. Antenna must exist permanently fastened to the unit. b. Antenna must employ a unique type of connector to attach to the EUT. c. Unit must be professionally installed, and installer shall be responsible for verifying that the right antenna is employed with the unit. Antenna Connector Construction The EUT has iv internal antennas arrangement, and the antenna gain is iii.0dBi, fulfill the requirement of the item. Delight refer to the internal photos. Effect: Compliance. FCC Part 15.247 Page eight of 47 Bay Surface area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A FCC §15.209, §15.205 & §15.247(d) - SPURIOUS EMISSIONS Applicable Standard FCC §15.247 (d); §15.209; §15.205; Measurement Uncertainty Compliance or not- compliance with a disturbance limit shall be determined in the following fashion： If Ulab is less than or equal to Ucispr of Table ii, then: –compliance is deemed to occur if no measured disturbance level exceeds the disturbance limit; –non - compliance is deemed to occur if any measured disturbance level exceeds the disturbance limit. If Ulab is greater than Ucispr of Table 2, and so: –compliance is deemed to occur if no measured disturbance level, increased by (Ulab − Ucispr), exceeds the disturbance limit; –non - compliance is accounted to occur if any measured disturbance level, increased by (Ulab − Ucispr), exceeds the disturbance limit. Based on CISPR 16-4-2-2011, measurement incertitude of radiated emission at a distance of 3m at Bay Area Compliance Laboratories Corp. (Dongguan) is: 30M~200MHz: 5.0 dB 200M~1GHz: 6.2 dB 1G~6GHz: 4.45 dB 6G~18GHz: 5.23 dB Table 2 – Values of Ucispr Measurement Radiated disturbance (electrical field forcefulness at an OATS or in a SAC) (30 MHz to 1000 MHz) Radiated disturbance (electric field force in a FAR) (ane GHz to 6 GHz) Radiated disturbance (electric field strength in a FAR) (6 GHz to 18 GHz) Ucispr 6.iii dB 5.ii dB five.5 dB EUT Setup Below 1GHz: FCC Part xv.247 Page ix of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Written report No.: RDG151015004-00A To a higher place 1GHz: The radiated emission tests were performed in the three meters chamber test site, using the setup accordance with the ANSI C63.10-2013. The specification used was the FCC 15.209, and FCC 15.247 limits. The spacing between the peripherals was 10 cm. EMI Test Receiver & Spectrum Analyzer Setup The system was investigated from 30 MHz to 25 GHz. During the radiated emission test, the EMI test receiver & Spectrum Analyzer Setup were set up with the following configurations: Frequency Range RBW Video B/Westward IF B/W Detector 30MHz – one thousand MHz 120 kHz 300 kHz 120kHz QP 1MHz 3 MHz PK 1MHz x Hz Ave. Above i GHz Examination Procedure Maximizing procedure was performed on the highest emissions to ensure that the EUT complied with all installation combinations. Information was recorded in Quasi-height detection fashion for frequency range of xxx MHz-1 GHz, peak and Average detection modes for frequencies above 1 GHz. FCC Part fifteen.247 Folio x of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated past adding the Antenna Loss and Cable Loss, and subtracting the Amplifier Gain from the Meter Reading. The basic equation is as follows: Corrected Amplitude = Meter Reading + Antenna Loss + Cablevision Loss - Amplifier Gain The "Margin" column of the following information tables indicates the degree of compliance with the applicable limit. For example, a margin of 7dB ways the emission is 7dB below the limit. The equation for margin adding is as follows: Margin = Limit – Corrected Aamplitude Test Equipment List and Details ESCI Series Number 100224 Scale Date 2015-08-03 Calibration Due Date 2016-08-02 Antenna JB3 A060611-3 2014-11-06 2017-xi-05 Amplifier 8447E 2434A02181 2015-09-01 2016-09-01 Agilent Spectrum Analyzer E4440A SG43360054 2014-12-04 2015-12-04 ETS-Lindgren Horn Antenna 3115 9808-5557 2015-09-06 2018-09-06 Mini-Excursion Amplifier ZVA-213-S+ 054201245 2015-02-xix 2016-02-19 R&Southward Ducommun Technolagies Spectrum Analyzer FSP 38 2015-05-09 2016-05-09 Horn Antenna ARH-4223-02 100478 1007726-01 1304 2014-06-16 2017-06-15 Quinstar Amplifier QLW18405536-JO 2015-09-06 2016-09-06 Manufacturer Description Model R&Due south Sunol Sciences HP EMI Test Receiver 15964001001 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Dongguan) attests that all calibrations have been performed, traceable to National Primary Standards and International System of Units (SI). Exam Results Summary According to the recorded data in following table, the EUT complied with the FCC Title 47, Role 15, Section 15.205, 15.209 and 15.247, with the worst margin reading of: 0.38 dB at 2483.5 MHz in the Vertical polarization Test Data Environmental Conditions Temperature: Relative Humidity: ATM Force per unit area: 28.9 °C 45 % 99.6 kPa The testing was performed by Allen Qiao on 2015-10-14. FCC Part fifteen.247 Page 11 of 47 Bay Expanse Compliance Laboratories Corp. (Dongguan) Written report No.: RDG151015004-00A Fashion: Transmitting (the test performed at worse mode determined by conducted output power examination) Frequency (MHz) Receiver Reading Detector (dBμV) (PK/QP/AV) 2406.5 2406.v 2406.5 2406.v 2390 2390 4813 4813 7219.5 7219.5 9626 9626 3700 3700 244.37 79.82 65.58 80.86 66.69 25.two thirteen.69 38.01 23.34 31.ix 18.5 34.28 26.55 37.24 24.85 52.iii PK AV PK AV PK AV PK AV PK AV PK AV PK AV QP 2436.5 2436.5 2436.five 2436.5 4873 4873 7309.v 7309.5 9746 9746 3700 3700 3130 3130 244.37 81.ii 66.93 81.82 67.58 39.67 24.35 32.34 eighteen.87 34.36 26.65 35.43 23.03 33.62 21.29 52.2 PK AV PK AV PK AV PK AV PK AV PK AV PK AV QP 2476.5 80.76 PK 2476.5 66.48 AV 2476.5 81.56 PK 2476.5 67.43 AV 2483.5 33.27 PK 2483.5 21.29 AV 4953 39.29 PK 4953 24.fifteen AV 7429.5 32.nineteen PK 7429.v 18.75 AV 9906 34.iii PK 9906 26.61 AV 3700 35.33 PK 3700 22.87 AV 244.37 52.i QP *Within measurement uncertainty! FCC Part 15.247 Rx Antenna Polar Factor (H/V) (dB/m) Cable loss (dB) Amplifier Proceeds (dB) Low Channel: 2406.5 MHz 28.48 3.67 0.00 28.48 3.67 0.00 28.48 3.67 0.00 28.48 iii.67 0.00 28.44 iii.63 0.00 28.44 3.63 0.00 33.16 5.05 27.41 33.16 v.05 27.41 36.40 half-dozen.63 25.91 36.40 half dozen.63 25.91 38.37 eight.54 27.51 38.37 viii.54 27.51 32.46 iv.64 27.33 32.46 4.64 27.33 12.25 1.89 21.49 Middle Channel: 2436.5 MHz 28.55 iii.75 0.00 28.55 3.75 0.00 28.55 iii.75 0.00 28.55 three.75 0.00 33.37 5.13 27.42 33.37 5.13 27.42 36.56 vi.74 25.88 36.56 half-dozen.74 25.88 38.35 eight.61 27.24 38.35 viii.61 27.24 32.46 4.64 27.33 32.46 iv.64 27.33 31.29 vi.92 27.43 31.29 6.92 27.43 12.25 1.89 21.49 Loftier Channel: 2476.5 MHz 28.64 3.69 0.00 28.64 3.69 0.00 28.64 3.69 0.00 28.64 three.69 0.00 28.66 3.67 0.00 28.66 3.67 0.00 33.64 5.36 27.43 33.64 5.36 27.43 36.77 six.88 25.94 36.77 6.88 25.94 38.32 viii.70 26.72 38.32 eight.lxx 26.72 32.46 iv.64 27.33 32.46 iv.64 27.33 12.25 1.89 21.49 Corrected Amplitude (dBμV/m) FCC 15.247 Limit Margin (dBμV/thou) (dB) 111.97 97.73 113.01 98.84 57.27 45.76 48.81 34.14 49.02 35.62 53.68 45.95 47.01 34.62 44.95 Due north/A Northward/A N/A North/A 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 46.00 Northward/A N/A N/A N/A 16.73 8.24 25.xix 19.86 24.98 18.38 20.32 eight.05 26.99 19.38 1.05 * 113.fifty 99.23 114.12 99.88 50.75 35.43 49.76 36.29 54.08 46.37 45.20 32.80 44.40 32.07 44.85 N/A Due north/A N/A N/A 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 46.00 N/A N/A N/A N/A 23.25 18.57 24.24 17.71 19.92 7.63 28.80 21.20 29.60 21.93 1.15 * 113.09 98.81 113.89 99.76 65.60 53.62 50.86 35.72 49.90 36.46 54.60 46.91 45.10 32.64 44.75 N/A North/A N/A Due north/A 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00 46.00 N/A N/A N/A N/A 8.40 0.38 * 23.14 eighteen.28 24.10 17.54 19.40 seven.09 28.90 21.36 i.25 * Page 12 of 47 Bay Expanse Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Conducted Spurious Emissions at Antenna Port Note: the test performed at high power Antenna 1 Low Channel Antenna 1 Middle Channel FCC Function xv.247 Page 13 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Antenna 1 High Aqueduct Antenna ii Low Aqueduct FCC Role 15.247 Page fourteen of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Written report No.: RDG151015004-00A Antenna two Middle Channel Antenna 2 Loftier Channel FCC Function xv.247 Page fifteen of 47 Bay Surface area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Antenna 3 Low Aqueduct Antenna 3 Middle Aqueduct FCC Part 15.247 Page 16 of 47 Bay Surface area Compliance Laboratories Corp. (Dongguan) Written report No.: RDG151015004-00A Antenna 3 Loftier Channel Antenna four Low Channel FCC Office 15.247 Page 17 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Antenna 4 Centre Channel Antenna iv High Aqueduct FCC Office fifteen.247 Folio 18 of 47 Bay Expanse Compliance Laboratories Corp. (Dongguan) Study No.: RDG151015004-00A FCC §15.247(a) (ii) – 6dB BANDWIDTH Applicable Standard Systems using digital modulation techniques may operate in the 902–928 MHz, 2400–2483.five MHz, and 5725–5850 MHz bands. The minimum 6 dB bandwidth shall be at least 500 kHz. Test Process 1. Bank check the calibration of the measuring instrument using either an internal calibrator or a known signal from an external generator. two. Position the EUT without connectedness to measurement instrument. Turn on the EUT and connect it to measurement instrument. Then fix it to whatsoever one convenient frequency inside its operating range. Set a reference level on the measuring musical instrument equal to the highest peak value. 3. Measure the frequency departure of two frequencies that were attenuated 6 dB from the reference level. Record the frequency difference as the emission bandwidth. 4. Echo above procedures until all frequencies measured were consummate. Spectrum Analyzer EUT Test Equipment List and Details Manufacturer Description Model Serial Number Calibration Date Calibration Due Appointment R&S Spectrum Analyzer FSEM 831259/019 2015-07-28 2016-07-27 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Dongguan) attests that all calibrations take been performed, traceable to National Primary Standards and International Organisation of Units (SI). Test Data Environmental Weather condition Temperature: Relative Humidity: ATM Pressure: 26.1 °C 58 % 99.4 kPa The testing was performed by Allen Qiao on 2015-10-13. Test Issue: Pass. Please refer to the following tables and plots. FCC Part xv.247 Folio 19 of 47 Bay Surface area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Examination Mode: Transmitting (the test performed at loftier power) Test Manner Antenna 1 Antenna 2 Antenna 3 Antenna iv FCC Part xv.247 Frequency 6 dB Bandwidth (MHz) (MHz) Low 2406.5 9.52 Middle 2436.5 ix.52 High 2476.5 9.52 Low 2406.v ix.52 Centre 2436.v 9.52 Loftier 2476.5 9.52 Low 2406.5 9.52 Eye 2436.5 nine.52 Loftier 2476.5 9.52 Low 2406.five 9.52 Middle 2436.5 nine.52 High 2476.five 9.52 Channel Page 20 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A vi dB Bandwidth: Antenna 1 Low Channel Antenna ane Center Channel FCC Part 15.247 Page 21 of 47 Bay Surface area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Antenna 1 High Aqueduct Antenna 2 Low Channel FCC Part 15.247 Folio 22 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Antenna 2 Middle Channel Antenna 2 High Channel FCC Part 15.247 Page 23 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Antenna three Low Channel Antenna iii Middle Channel FCC Part 15.247 Page 24 of 47 Bay Expanse Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Antenna three High Aqueduct Antenna four Low Channel FCC Part 15.247 Page 25 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Antenna 4 Center Channel Antenna 4 High Aqueduct FCC Part xv.247 Page 26 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Study No.: RDG151015004-00A FCC §15.247(b) (iii) - MAXIMUM Acme CONDUCTED OUTPUT Power Applicative Standard According to FCC §xv.247(b) (3), for systems using digital modulation in the 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz bands: 1 Watt. Equally an alternative to a peak ability measurement, compliance with the 1 Watt limit can be based on a measurement of the maximum conducted output power. Maximum Conducted Output Power is divers equally the full transmit power delivered to all antennas and antenna elements averaged beyond all symbols in the signaling alphabet when the transmitter is operating at its maximum power command level. Power must be summed across all antennas and antenna elements. The average must not include any time intervals during which the transmitter is off or is transmitting at a reduced ability level. If multiple modes of operation are possible (due east.g., culling modulation methods), the maximum conducted output power is the highest full transmit power occurring in whatever mode. Test Procedure 1. According to KDB 558074 D01 DTS Meas Guidance v03r03, place the EUT on a bench and fix information technology in transmitting style. 2. Remove the antenna from the EUT and and so connect a low loss RF cable from the antenna port to a Examination Equipment. Test Equipment EUT Test Equipment List and Details Manufacturer Agilent Agilent Agilent Description Wideband Power Sensor Wideband Ability Sensor P-Serial Ability Meter Model Serial Number Calibration Date Scale Due Date N1921A MY54210016 2014-11-03 2015-11-03 N1921A MY54170013 2014-11-03 2015-xi-03 N1912A MY5000448 2014-eleven-03 2015-xi-03 * Statement of Traceability: Bay Surface area Compliance Laboratories Corp. (Dongguan) attests that all calibrations have been performed, traceable to National Primary Standards and International System of Units (SI). FCC Part 15.247 Page 27 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Test Data Environmental Conditions Temperature: Relative Humidity: ATM Pressure: 26.iii °C 57 % 99.6 kPa The testing was performed past Allen Qiao on 2015-10-xiv. Test Mode: Transmitting Channel Frequency MHz Low Middle High 2406.5 2436.5 2476.5 Low Middle High 2406.v 2436.five 2476.v Conducted Peak Output Power (dBm) Ant. 1 Emmet. ii Ant. iii Pismire. 4 High Power 26.41 25.98 26.80 26.50 25.83 25.28 26.68 26.35 25.37 24.73 25.55 25.twoscore Low Ability iv.56 4.86 v.38 five.50 ii.57 2.97 3.33 3.40 -0.xxx -0.24 0.53 1.11 The system employed Space Time Cake Codes (STBC) engineering, and the signals are completely uncorrelated, the system configured two antennas with high power for good operation, and the rest antennas were configured with low power, the worst case in the following table: Channel Frequency Conducted Elevation Output Power (dBm) Ant. 2 Ant. three Emmet. 4 MHz Ant. i Low 2406.5 four.56 4.86 26.fourscore Middle 2436.five 2.57 two.97 High 2476.5 -0.30 -0.24 FCC Part 15.247 Limit Result Total dBm 26.l 29.69 thirty Pass 26.68 26.35 29.55 30 Pass 25.55 25.twoscore 28.five xxx Pass Folio 28 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A FCC §15.247(d) – 100 kHz BANDWIDTH OF FREQUENCY Band Border Applicative Standard In any 100 kHz bandwidth exterior the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency ability that is produced by the intentional radiator shall be at least 20 dB beneath that in the 100 kHz bandwidth within the ring that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the utilize of RMS averaging over a time interval, as permitted nether paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in §15.209(a) is non required. In add-on, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in §15.209(a) (encounter §fifteen.205(c)). Test Process 1. Check the scale of the measuring instrument using either an internal calibrator or a known signal from an external generator. ii. Position the EUT without connection to measurement instrument. Turn on the EUT and connect its antenna terminal to measurement instrument via a low loss cablevision. Then set information technology to any 1 measured frequency within its operating range, and make certain the instrument is operated in its linear range. 3. Set up RBW to 100 kHz and VBW of spectrum analyzer to 300 kHz with a convenient frequency bridge including 100 kHz bandwidth from band edge. 4. Measure the highest amplitude appearing on spectral brandish and set up it as a reference level. Plot the graph with marking the highest point and edge frequency. v. Echo in a higher place procedures until all measured frequencies were complete. Test Equipment Listing and Details Manufacturer Description Model Serial Number Calibration Date Calibration Due Appointment R&Due south Spectrum Analyzer FSEM 831259/019 2015-07-28 2016-07-27 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Dongguan) attests that all calibrations have been performed, traceable to National Chief Standards and International System of Units (SI). Test Data Environmental Conditions Temperature: Relative Humidity: ATM Pressure: 23.8 °C 53 % 99.6 kPa The testing was performed by Allen Qiao on 2015-ten-13. Examination Result: Compliance (the test performed at high power) FCC Function 15.247 Page 29 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Written report No.: RDG151015004-00A Please refer to following plots. Antenna 1: Band Edge, Left Side Antenna 1: Band Border, Correct Side FCC Part 15.247 Page 30 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Study No.: RDG151015004-00A Antenna 2: Band Edge, Left Side Antenna 2: Band Border, Right Side FCC Part fifteen.247 Folio 31 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Antenna 3 Band Edge, Left Side Antenna 3 Band Edge, Right Side FCC Role xv.247 Page 32 of 47 Bay Surface area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Antenna 4 Band Edge, Left Side Antenna iv Band Edge, Right Side FCC Part 15.247 Folio 33 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A FCC §15.247(e) - Power SPECTRAL DENSITY Applicative Standard For digitally modulated systems, the ability spectral density conducted from the intentional radiator to the antenna shall not be greater than eight dBm in whatever three kHz band during any time interval of continuous transmission. This power spectral density shall be determined in accordance with the provisions of paragraph (b) of this section. The same method of determining the conducted output power shall exist used to decide the power spectral density. Test Procedure 1. Check the calibration of the measuring instrument using either an internal calibrator or a known signal from an external generator. 2. Position the EUT was set without connection to measurement instrument. Turn on the EUT and connect its antenna final to measurement instrument via a low loss cable. Then set it to any 1 measured frequency within its operating range, and make sure the instrument is operated in its linear range. 3. Set the RBW = 3 kHz, VBW = 10 kHz, Prepare the bridge to one.5 times the DTS bandwidth. 4. Apply the peak mark function to make up one's mind the maximum aamplitude level. Test Equipment List and Details Manufacturer Description Model Serial Number Calibration Date Scale Due Date R&Southward Spectrum Analyzer FSEM 831259/019 2015-07-28 2016-07-27 * Argument of Traceability: Bay Area Compliance Laboratories Corp. (Dongguan) attests that all calibrations have been performed, traceable to National Primary Standards and International System of Units (SI). Test Data Environmental Conditions Temperature: Relative Humidity: ATM Force per unit area: 25.8 °C 53 % 99.4 kPa The testing was performed by Allen Qiao on 2015-10-13. Test Manner: Transmitting FCC Part 15.247 Page 34 of 47 Bay Expanse Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Test Event: Pass Test Fashion: Transmitting Channel Frequency MHz Low Centre High 2406.5 2436.five 2476.five Low Middle High 2406.v 2436.5 2476.five Power Spectral Density (dBm/3kHz) Ant. ane Ant. ii Ant. 3 High Power -10.57 -ten.09 -9.80 -10.44 -10.35 -nine.75 -10.78 -ten.87 -10.09 Low Power -31.24 -31.24 -30.42 -32.18 -31.75 -31.93 -35.95 -35.eighty -35.14 Pismire. 4 -10.05 -9.98 -10.34 -31.09 -32.08 -35.35 The organization employed Infinite Time Block Codes (STBC) engineering science, and the signals are completely uncorrelated, the system configured two antennas with loftier power for good performance, and the remainder antennas were configured with depression power, the worst case in the following table: MHz Pismire. 1 Ability Spectral Density (dBm/3kHz) Pismire. 2 Ant. iii Emmet. 4 Low 2406.5 -31.24 -31.24 -9.80 -10.05 -6.88 Pass Centre 2436.5 -32.18 -31.75 -9.75 -nine.98 -6.83 Laissez passer High 2476.five -35.95 -35.80 -10.09 -10.34 -vii.nineteen Pass Channel Frequency Limits Upshot Total dBm/3kHz Please refer to the following plots FCC Part fifteen.247 Page 35 of 47 Bay Expanse Compliance Laboratories Corp. (Dongguan) Study No.: RDG151015004-00A Low Power: Power Spectral Density, Antenna ane Low Channel Power Spectral Density, Antenna 1 Middle Channel FCC Part xv.247 Folio 36 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Written report No.: RDG151015004-00A Power Spectral Density, Antenna 1 Loftier Channel Power Spectral Density, Antenna 2 Low Channel FCC Role 15.247 Folio 37 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Power Spectral Density, Antenna two Centre Channel Ability Spectral Density, Antenna 2 Loftier Channel FCC Part fifteen.247 Folio 38 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Written report No.: RDG151015004-00A Power Spectral Density, Antenna iii Depression Channel Ability Spectral Density, Antenna 3 Middle Channel FCC Role fifteen.247 Page 39 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Ability Spectral Density, Antenna three High Channel Power Spectral Density, Antenna 4 Low Channel FCC Part 15.247 Folio forty of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Power Spectral Density, Antenna 4 Centre Channel Power Spectral Density, Antenna iv High Channel FCC Part 15.247 Page 41 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A High Ability: Power Spectral Density, Antenna 1 Low Aqueduct Ability Spectral Density, Antenna i Middle Aqueduct FCC Function xv.247 Page 42 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Power Spectral Density, Antenna 1 High Aqueduct Power Spectral Density, Antenna 2 Low Channel FCC Office xv.247 Page 43 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Ability Spectral Density, Antenna two Middle Channel Power Spectral Density, Antenna 2 High Channel FCC Part 15.247 Page 44 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Power Spectral Density, Antenna 3 Low Channel Power Spectral Density, Antenna 3 Middle Channel FCC Part 15.247 Page 45 of 47 Bay Area Compliance Laboratories Corp. (Dongguan) Written report No.: RDG151015004-00A Power Spectral Density, Antenna 3 Loftier Channel Power Spectral Density, Antenna 4 Depression Channel FCC Function 15.247 Page 46 of 47 Bay Surface area Compliance Laboratories Corp. (Dongguan) Report No.: RDG151015004-00A Power Spectral Density, Antenna 4 Centre Channel Power Spectral Density, Antenna 4 High Channel *****END OF Study***** FCC Function 15.247 Page 47 of 47
Dji Inspire 1 V2 0 Test,
Source: https://fccid.io/SS3-WM6101510/Test-Report/Test-Report-2799193
Posted by: schaffersinut1943.blogspot.com
0 Response to "Dji Inspire 1 V2 0 Test"
Post a Comment